Twin softening systems with hard water sensor (1in.) Twin softening systems with hard water sensor Sensor initiates one of two cartridges to automatically regenerate Features include error messages and automatic switch off (LED lights) Potential free contact for connection to a central fault collector, which allows the system to be connected to the users central error collection monitor Water connections are R 1 in. 230V/50Hz Twin softening system with hard water sensor (2 in.) Twin softening systems with hard water sensor Sensor initiates one of two cartridges to automatically regenerate Top mounted with inlet and outlet pipe bridge fitted with automatic switchover and electronic sensor control, making the system easier to install Fault-triggered switch off with hard water as well as signal output and potential free contact for fault messages — If error isn’t addressed, system will automatically turn off Connector for solenoid or membrane valve Glass-fiber pressure container Brass automatic valve with 4-stage regeneration procedure Water connections are R2 in. 230V/50Hz Ordering Information: This product is not available in all regions
Double Softening System WAT
$0.00
For continuous production of softened water. Thermo Scientific™ Double Softening System WAT includes a hardness sensor control that automatically regenerates resin once hardness is detected in one of the two cartridges. This ready-to-connect water softener is for softening feed water before feeding a reverse osmosis system. Water softening removes hard ions, such as calcium and magnesium, and extends the life of the reverse osmosis membrane.
Description
Additional information
| Capacity (Metric) |
2 x 120 m³ at 10°dH |
|---|---|
| Feed Water Monitoring |
Yes |
| Flow Rate |
14 L/hr. |
| Type |
Water Softening System, WAT |
| Salt Stock |
400 kg |
| Width (Metric) |
2540 mm |
| Height (Metric) |
2150 mm |
| Depth (Metric) |
900 mm |
| Unit Size |
Each |
Reviews (0)
Shipping & Delivery
Related products
Сatalog number:
AY1406X3
Accessories for the Barnstead™ TII Type 2 Water System
Сatalog number:
50132389
Barnstead™ Pacific™ RO Water Purification System
Сatalog number:
50155482
Reverse Osmosis Systems RO 100-350 RDS
Produce product water that is less than 0.1µS/cm. Thermo Scientific™ Reverse Osmosis RO 100-350 RDS systems features an integrated ion exchanger, storage tank and pressure pump in a dust-proof cabinet. These systems are ideal supplier of high purity water for analyzers, as well as for general laboratory purposes according to international quality-standards like CLSI. The quality of the high purity water supplied by reverse osmosis is not sufficient when a conductivity below 1μS/cm is required. For such cases, the combination of reverse osmosis with ion exchanger is necessary.
Сatalog number:
50131323
Barnstead™ GenPure™ xCAD Water Purification System
Сatalog number:
50136172
Barnstead™ GenPure™ xCAD Plus Ultrapure Water Purification System
Gain flexibility in the lab with the Thermo Scientific™ Barnstead™ GenPure™ xCAD Plus Ultrapure Water Purification System. Its advanced technologies allow for simultaneous dispensing from up to three remote dispensers for ease of use in shared laboratory environments. This lab water system comes with leak detection, electronic dispensing for fully automatic volume control and feed water monitoring that alerts users to fluctuations in the feed water quality. All consumables needed for start-up come with the system, allowing for simple ordering and setup.
Сatalog number:
LMX31
Barnstead™ RO and TII Accessories and Consumables
Optimize your water purification system with Thermo Scientific™ Barnstead™ RO and TII Accessories and Consumables. For use with Barnstead RO and TII water purification systems, these products include filters and pre-filters, cartridges, overflow cutoff float and pump interlock cable, as well as dispensers and printer.
Сatalog number:
D13321
Barnstead™ Easypure™ RoDi
Сatalog number:
50157375
Reviews
There are no reviews yet.